View and Download Kawasaki Ninja service manual online. Ninja Motorcycle pdf manual download. Also for: Ninja abs, Er-6f, Er-6f abs. Visit Kawasaki Motor Corps., USA owners center for up to date service manuals, parts diagrams, ROK™ info, owner support, warranty info, Kawasaki Protection. Kawasaki NINJA R User Manual • Preparation • Kawasaki Motorcycles.

Author: Fegore Togor
Country: Paraguay
Language: English (Spanish)
Genre: Sex
Published (Last): 4 December 2014
Pages: 338
PDF File Size: 10.13 Mb
ePub File Size: 17.9 Mb
ISBN: 662-1-29238-189-4
Downloads: 48177
Price: Free* [*Free Regsitration Required]
Uploader: Brashicage

Water Temperature Sensor Circuit 1. Measure the clearance when engine is cold. Sealant – Liquid Gasket, TB Never touch a hot engine. Motorcycle Kawasaki Ninja Service Manual pages. Air suction valve damaged Piston oil ring worn Air switching valve damaged Cylinder worn Run the rear brake light switch lead through the hole on frame. If the connector is corroded or dirty, clean it carefully.

Main Fuse 30 A 6. Removal may damage them. Air Cleaner Housing Seat Height mm Fix the turn signal relay to the frame. Do not use fluid from a container that has been left unsealed or that has been open for a long time. Torque – Oil Pan Bolts: Be sure to strictly follow the Battery Service instructions in this Manual. Intake Air Temperature Sensor 3. Hook Hold the rear brake light switch lead and the crankshaft sensor lead.

First turn the cap counterclockwise to the first stop. Replace any damaged gears or gears with excessively worn dogs or dog holes.


Insert the ignition key into the seat lock, lo- cated under the seat cover. How To Use This Manual Be alert for problems and non-scheduled ticular interest for more efficient and con- maintenance. If the frame is bent, dented, cracked, or warped, replace it. Activating the battery requires two steps, fill- ing the battery with electrolyte, and charging.

Preparation – Kawasaki NINJA 650R User Manual

If there is any damage to the frame, replace it. Main Fuse 30 A 9. To print the manual completely, please, download it.

Service Code 51, 52 Stick Coil Circuit 1. Brake Line Bleeding The brake fluid has a very low compression coefficient so that almost all the movement of the brake lever or pedal is transmitted directly to the caliper for braking action.

Torque – Oil Filter: If any plates show signs of damage, or nimja they have worn past the service limit, replace them with new ones. Do not re- move the muffler while it is hot. 65r0 Ground 1 3. Throttle Full Open UR: Cylinder head gasket damaged Spark plug loose Cylinder head warped Cylinder head not sufficiently tightened Valve spring broken or weak down Valve not seating properly valve bent, No valve clearance worn, or carbon accumulation on the Cylinder, piston worn seating surface Piston ring bad worn, weak, broken, or Torque – Caliper Bleed Valve: Pump the brake lever until it becomes hard, and apply the brake and hold it [A].

The relays and diodes can not be removed. Page LED goes off. But the service codes stored in memory of the ECU are not erased to preserve the problem history.


Clamp Hold the headlight lead as shown.

Download Owners Manuals

License Plate Light 12 V 5 W So, the heater itself can not be removed. Spring Preload Setting Standard Position: Bearing Remover Shaft, 650rr 12 V 10 Ah 7. Clamp Hold the main harness.

Electrolyte over capacity can lead to battery cranking or leaking and result in corrosion damage to the vehicle. If the breather plate [A] is to be removed, follow the next procedure. Preparation Battery Service Battery Removal The battery used in this motorcycle is a sealed type and never needs to be refilled.

If the bearing is removed, it will need to be replaced with a new one. Don’t have an account? 650rr

Kawasaki Ninja – Owner’s Manual – Pages – PDF

Fix the ignition switch lead connector upper and the left switch housing lead connector lower to the bracket. Special Tool – Hand Tester: Torque – Upper Crankcase Bolts: Al- though no adjustments are required, a thorough visual in- manuxl must be made at the intervals specified by the Pe- riodic Maintenance Chart. Also, check to see that each cotter pin is in place and in good condition.