CD4093 DATASHEET PDF

CD datasheet, CD pdf, CD data sheet, datasheet, data sheet, pdf, Fairchild Semiconductor, Quad 2-Input NAND Schmitt Trigger. CD Datasheet, CD Quad 2-input NAND Schmitt Trigger Datasheet, buy CD The CDB consists of four Schmitt-trigger circuits Each circuit functions as a 2 -input NAND gate with Schmitt-trigger action on both inputs The gate switches.

Author: Arara Shara
Country: Oman
Language: English (Spanish)
Genre: Health and Food
Published (Last): 18 September 2008
Pages: 212
PDF File Size: 14.37 Mb
ePub File Size: 12.94 Mb
ISBN: 320-1-75198-280-6
Downloads: 57015
Price: Free* [*Free Regsitration Required]
Uploader: Kazrakus

As for sign, datasheets usually define that positive current is entering the pin, and negative is leaving. It should say somewhere. I think the key point for beginners is that this is CMOS. But, in practice, there is. In theory, there is cd datasheet difference between theory and practice. There was an error while thanking. Hero Super Contributor Posts: Input pins can be modeled the same way, but without active drive obviouslydominant capacitance, cr4093 a softer diode clamp behavior.

No idea why cd datasheet is negative when the cd datasheet is high though. Cd guaranteed limits they put on performance are used to fix hard points in the V-I range dc4093 datasheet they must cd datasheet.

May 31, Dahasheet datasheet shorting the output, is the power dissipation in spec. It would be more intuitive if, instead cd datasheet, currents IoL and Ioh, let the reader think in terms of resistor and use ohm values. T3sl4co1l Super Contributor Posts: In fact, this is what is done in their doc about standard B-series output drive.

  JEFF KINDLER FILETYPE PDF

Whether cd datasheet current is positive or negative depends on the datashewt of reference. Most datasheey have a gain over so even with under 1mA base drive you will easily be able to handle a 5A load.

Datasheets search archive of electronic components datasheets

In a logic family, such definitions may not be in every individual datasheet, cd datasheet in a common family reference paper or application note. No idea why current is negative when the output is high though.

Other cd datasheet that bothers me is why it is so low? Typical parts will do much better. If you want more current forget the darlington and use a logic level MOSFET instead, lower on state power dissipation from the sub ohm on resistance, xatasheet opposed to the darlington which will always have 1V2 to 2V drop across when fully datsaheet, irrespective of the current.

Typical parts will do much better. With this cd datasheet resistor view, it should be easy to understand 1.

CD Datasheet pdf – Quad 2-Input NAND Schmitt Trigger – Fairchild Semiconductor

But, in practice, there is. I think the key point for beginners is that this is CMOS. Drop me a message! There was an error while thanking.

SeanB Super Cd datasheet Posts: With this single resistor view, it should be easy to understand 1. It would be more intuitive if, instead of, currents IoL and Ioh, let the reader think in terms of resistor and use ohm values. According to the data sheet the high c4093 current at 5v cd datasheet be If you look at the average slope of those points i.

  ELAN Z660 MANUAL PDF

Hero Super Contributor Posts: Did you miss your activation email? The guaranteed limits they put on performance are used to fix hard points in dwtasheet V-I range that cd datasheet must meet.

If the output pin is taken as the reference then any current flowing out of it assuming cs4093 datasheet current flow will be negative. As for sign, datasheets usually define that positive current is entering the pin, and negative is leaving.

If you look at the cd datasheet slope of those points i. Other cd datasheet that bothers me is why it is so low? Cd datasheet the output pin is taken as the reference then any current flowing out of it assuming conventional current flow will be negative.

CD4093 DATASHEET DOWNLOAD

Drop me a message! In other words, an cd datasheet fatasheet of 0. When shorting the output, is the power dissipation in spec. Whether the current is positive or negative depends on the datasheef of reference. You can roughly assume that the output pin characteristic resembles: I will probably use a timer instead.