CONFIGURATION ROUTAGE OSPF PDF

This document uses these configurations. ip unnumbered Ethernet2/0/0 router ospf 1 network area 0. Redistribution Configuration Syntax and Examples. IGRP and EIGRP. OSPF. RIP. Redistributing Static Routes Except Gateway of Last resort in. This article describes some basic OSPF configuration.

Author: Kigagrel Zuluzahn
Country: Ethiopia
Language: English (Spanish)
Genre: Literature
Published (Last): 18 January 2006
Pages: 37
PDF File Size: 11.97 Mb
ePub File Size: 20.77 Mb
ISBN: 771-1-96757-799-4
Downloads: 11801
Price: Free* [*Free Regsitration Required]
Uploader: Daijora

NOTE We have used the router-id 1. Area IDs are unique numeric identifiers, in dotted decimal notation. For example, here is the output of the command on R R3 is in the area 1. To verify if the routing updated were exchanged, we can use the show ip route command. Because R1 connects only to R2, we only need to establish a neighbor relationship with R2 and advertise directly connected subnet into OSPF.

Jan 26, upravnik.

OSPF configuration

First, we need to enable OSPF on both routers. For a single-area OSPFv3 network, include the ospf3 statement at the [edit protocols] hierarchy level. Confirm that the Area field displays the value that you configured.

Configuration of R3 looks similar, but with one difference, namely area number.

OSPF configuration

We can verify that the routers have become neighbors by typing the show ip ospf neighbors command on either router:. We can do that using the following sequence of commands:. To confirm your OSPFv3 configuration, enter the show protocols ospf3 command.

  ENTREVISTA PORFIRIO DIAZ CREELMAN PDF

Configure the device interfaces. Confirm your configuration by entering the show protocols ospf command. We can verify that by using the show ip ospf neighbor command:. To do that, the following configuration on R1 will be used:.

Then we need to define what network will be advertised into OSPF. Configure the router identifiers for the devices in your OSPF network. To do that, we need to specify different area ID for each neighbor relationship, 0 for R1 and 1 for R2.

In an autonomous system ASthe backbone area is always assigned area ID 0. Our goal is to advertise the subnets directly connected to Toutage and R3. You must also create a backbone area if your network consists of multiple areas. This can be done by using the following sequence of commands on both routers:. As you can see from the network topology depicted above, routers R1 and R3 are in the area 0 and area 1, respectively.

Characters IA in front of the routes indicate that these routes reside in different areas. Next, you need to define on which interfaces OSPF will run and what networks will be advertised. To quickly configure a single-area OSPF network, copy the following commands, paste them into a text file, remove any line breaks, change any details necessary to match your network configuration, copy and paste the commands into the CLI at the [edit] hierarchy configurration, and then enter commit from configuration mode.

  INTERCOLLEGIATE MRCS REVISION NOTES PDF

Configuration du routage ospf – routeur Cisco

Area IDs need only be unique within an AS. Home About Contact Support our work. Routabe verify if directly connected subnets are really advertised into the different area, we can use the show ip route ospf command on both R1 and R All other networks or areas in ospg AS must be directly connected to the backbone area by area border routers that have interfaces in more than one area. We will use the following network topology:.

In this example we have two OSPF areas — area 0 and area 1. The network commands entered on both routers include subnets directly connected to both routers. OSPF basic configuration is very simple. Now R2 should have neighbor relationship with both R1 and R3.

If the output does not display the intended configuration, repeat the instructions in this example to correct the configuration.