DENSEN DM 10 PDF

Densen DM (£). “The Densen sounds excatly as it looks – big and lush. You’ll never find music thin or insubstantial if you’ve got one plugged in.”. Specifications. Power output: 75 watts per channel into 8Ω (stereo). Frequency response: 2Hz to kHz. Total harmonic distortion: %. Input sensitivity. Densen Audio DM Integrated Amplifier. Integrated pre- amp/power amp, 75 watts rms output per channel into 8 Ohms, four line-level inputs, two tape inputs.

Author: Daibei Dagami
Country: Tajikistan
Language: English (Spanish)
Genre: Music
Published (Last): 22 July 2010
Pages: 23
PDF File Size: 4.82 Mb
ePub File Size: 4.19 Mb
ISBN: 964-8-91548-793-6
Downloads: 11810
Price: Free* [*Free Regsitration Required]
Uploader: Merisar

One of the most important design characteristics of these amplifiers is the lack of global negative feedback. There are separate windings for the output stages bipolar transistors censen the remaining portions of the amplifiers the DM as well as the B In fact, the LED on the DM took 45 minutes to completely turn off since it is connected to the power capacitors.

A red LED in between the two brass control knobs illuminates when the units are on, and slowly fades when turned off. Because the DM and B use no global negative feedback, the damping factor is very modest.

In other words, they can only be used for tape recording and playback rather than for a “loop” containing an equalizer for tone control or other circuit such as a surround sound processor. The box and foam rubber protection weigh as much as some amplifiers! The upper portion of the audio spectrum is laid back, not quite as much as the SET, but just a little, and the mid-range is glorious, just like the SET.

We obtained not only the DM for testing, but the new BEAT B as well, and, as you will see, both amplifiers are very special in sound quality as well as their design.

  HAVIGHURST DEVELOPMENTAL TASKS PDF

In other words, they can deensen be used for tape recording dejsen playback rather than for a dnesen containing an equalizer for tone control or other circuit such as a surround sound processor.

Densen DM-10 Integrated Amplifiers

Unlike the SET, however, the bass region on the Densens is powerful and deep. There are proponents and opponents of negative feedback, densn of its shortcomings, and Densen has chosen the design route of using no global feedback which is very difficult to do in a solid state push-pull amplifier.

The box and foam rubber protection weigh as much as some amplifiers! The sibilants are clean, and female voices a good test for an amplifier are sweet and untainted.

Each amp is black with large brass knobs. La descrizione sopra e del modello a 50 wattmentre la scheda del modello fotografato e riferita al modello da 75 watt. For the DM, there are 40, microfarads of capacitance for the input stages and fensen same for the output, while the B uses 10, microfarads for the input, and 30, for the output. Di cosa si tratta. The amplifiers are built partially by robot, and partially by hand assembly.

The tape inputs and outputs are not tape loops. The DM uses two toroidal transformers one for each channeland the B uses one censen supplies both channels.

The amplifiers are built partially by robot, and partially by hand assembly. Our Vault pages may have some display quirks. Both the DM and the B are among the finest integrated amplifiers we have ever heard.

However, either amplifier can be used with a surround sound processor if the processor has the capability of routing the unprocessed signal through when it is turned off. Even harsh CDs are mellow when played through a Densen, just like a SET, and yet the volume is there when desired because high current is available the SET typically has an output of only 7 – 12 watts per channel.

  CONVOCATORIA ENARM 2009 PDF

Because the DM and B use no global negative feedback, the damping factor is very modest.

Densen DM10 MKII Stereo Integrated Amplifier | eBay

There are separate windings for the output stages bipolar transistors and the remaining portions of the amplifiers the DM as well as the B The basic difference between the DM and B is in dynamic range, and perhaps a bit in the detail of the upper mid-range as well as the high end.

Therefore, good speaker cables with low capacitance should be chosen for the best performance. Di cosa si tratta Integrato 75 watt. Unpacking the amplifiers is an experience in itself.

This is in keeping with Densen’s philosophy of not simply having a low profile, but allowing as little circuitry in the signal path as possible. In any case, this is one of the very few amplifier designs we have ever tested that has this type of sound characteristic, and we consider it an extremely desirable one.

Densen DM10 MKII Stereo Integrated Amplifier

Please explain the problem you are having. Both the DM and the B are among the finest integrated amplifiers we have ever heard. The DM uses two toroidal transformers one for each channeland the B uses one which supplies both channels.