M4 – 1 click=2 MOA. • When zeroing The recommended mounting position of the M68 CCO is the forward rail slot on . On a 25 meter M16A2 zeroing target. A Battle Sight Zero allows you to aim center mass on a target and achieve a hit from zero to meters. . M16A4. M4/M4A1. Carrying Handle. Windage. ½ MOA. 1 MOA. Carrying Handle. Elevation. 1 ½ MOA CCO (Windage and. Elevation). feedback (Figure 10). The M Sight, RCO, when installed on a M4/M4A1/ M16A4/M16A2, is zeroed on a standard M16 zero target with alternate strike points.
Place the red dot center mass of zdro target, and then engage. The students tighten the torque limiting knob until they hear 2 audible clicks. When the visible laser is adjusted to the reference point at 2 meters, then start the procedure again at 10 meters.
Share buttons are a little bit lower. Position your head so that one eye can focus on the red dot and the other eye can scan downrange. Your fingertip will appear to have moved, even though no movement has actually taken place. With your nonfiring hand, grasp the handguards toward the front sling swivel. The soldiers fire at single and multiple timed targets.
The precise boresighting of a laser will allow direct engagement of targets without a meter zero. The M68 will not retain its zero if mounted this way. Drop a comment on a post or contact us so we can take care of it! This will cause an ezro zero. The system performance improvements include a higher velocity rocket motor that extends the weapon effective range, increased lethality warheads, lower more consistent trigger release force, rifle cxo sight system, and better overall system reliability and safety.
There are three models:. With the vehicle not moving, the tires are cold.
FM Chapter 8 Advanced Optics, Lasers, And Iron Sights (Phase V of
T AP the forward assist assembly to ensure bolt closure. Align the borelight laser with the circle on the meter target offset. Bipod-mounted weapons are grounded on bipods with all muzzles facing downrange and away from nearby Soldiers.
While gripping the handguards with your nonfiring hand, extend your index finger to the front, automatically aiming the weapon on a line towards the target. Zeroing the M68 CCO using a zeroed weapon 1. When the target is detected the soldier orients his weapon around the base of the target, activates his laser, and walks the laser to the center mass of the target for engagement.
TRAINING SUPPORT PACKAGE (TSP) – ppt download
In every organization, all members must continue to practice certain skills to remain proficient. The visible laser of the borelight must be aligned with the barrel of your assigned weapon.
The 10 meter boresight target and 25 meter offset does not support the M68 CCO without the half moon spacer installed. Sight picture, if you recall, is the incorporation of the aligned CCO Dot with a target.
Take another shot to check that the point of impact is centered. tadget
TRAINING SUPPORT PACKAGE (TSP)
Tarrget three levels, in descending order of restriction, follow:. Using an SOP can reduce the number of oral orders needed to control fire. This will provide enough ambient light for the gunner to see the target.
Using the adjusters on the borelight, move the visible laser to the reference point. This requires the firer to ensure that he acquires the same sight picture and cheek-to-stock weld position each time in order to get a solid boresight. Starting with a securely installed and live-fire zeroed BIS, zefo the reflex sight to the front of the receiver rail or to the top RAS as preferred.
If immediate action does not remedy the problem, the following actions may be necessary to restore the weapon to operational condition:.
Unlike the original AT4, these models can be fired targey from within a room or other protected enclosure. The weapon can be stabilized in a rifle box rest or in a field location by laying two rucksacks side by side.
Toes are pointed straight to the front direction of movement. My presentations Profile Feedback Log out. Close the front lens cover before turning the rotary switch counterclockwise farget the OFF position. With the information given on top of the printed Aimpoint shooting target, and by counting targeh number of squares between the actual point of impact and the desired point of impact on the target, you can quickly and precisely detemine how many clicks you need to move the adjustment screws in order to zero your sight see image “Target 2”.
Tighten the mounting bolt through the carrying handle into the mounting bracket by hand. Unscrew and remove the protective caps from the adjustment turrets to access the targte screws.
Privacy & Cookies Policy
Necessary cookies are absolutely essential for the website to function properly. This category only includes cookies that ensures basic functionalities and security features of the website. These cookies do not store any personal information.